This exam is only to be completed after all of the task above have been completed and advised by your trainer.
The pass mark for this exam is 80%.
0 of 49 questions completed
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading…
You must sign in or sign up to start the quiz.
You must first complete the following:
Time has elapsed
You have reached 0 of 0 point(s), (0)
Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)
Question 1 of 49
What is the most important task to carry out before commencing work?
Question 2 of 49
To ensure that the door is working correctly before you start the service, you should?
Question 3 of 49
For safe working, you should ensure that –
Question 4 of 49
Which parts of the door system should be lubricated?
Question 5 of 49
A build-up of dust in a safety sensor will result in?
Question 6 of 49
Some manufacturers recommend that a drive belt is changed every –
Question 7 of 49
To keep the bottom of a sliding door in alignment, which of the following is fitted –
Question 8 of 49
When a drive arm is installed on a swing door, to ensure that the door is kept in the closed position, it should always be –
Question 9 of 49
On a sliding door, the purpose of the counter rollers is to –
Question 10 of 49
When should you replace a floor guide?
Question 11 of 49
On a swing door, a pivot is fitted to keep the door at the correct –
Question 12 of 49
The gaps around any door leaf should be –
Question 13 of 49
When checking the door alignment, you should also check –
Question 14 of 49
If the door alignment is adjusted then you should ensure –
Question 15 of 49
End stops are fitted on a sliding door to ensure this position –
Question 16 of 49
To ensure that the operator is securely fixed, you should –
Question 17 of 49
Wiring should be secured and tidy to ensure that –
Question 18 of 49
On a sliding door, if you found that the distance between the door and the frame was less than 25mm, you would –
Question 19 of 49
When cleaning the sensors during a service, you must not use –
Question 20 of 49
Which of the following will determine whether you can safely refit the cover to the operator?
Question 21 of 49
When refitting covers to sensors, care must be taken to ensure that –
Question 22 of 49
To ensure that the operator is protected, which of the following is correct?
Question 23 of 49
To determine whether you can safely remove the cover on an operator, you should carry out a –
Question 24 of 49
When carrying out the checklist, you are testing the door to which of the following standards?
Question 25 of 49
Which of the following tools are used to test an automatic door?
Question 26 of 49
The serial number of the automatic door should be on the operator and also within the –
Question 27 of 49
The usable aperture that a person can walk through is known as?
Question 28 of 49
The time that the door stands at the open position before it starts to close, is known as?
Question 29 of 49
On a swing door, what consideration must be taken into account when measuring the activation distance on the opening side?
Question 30 of 49
To reduce the risk of drawing in, shearing or crushing, the distances required are?
Question 31 of 49
Which of the following is used to test an ESPE safety sensor?
Question 32 of 49
When testing an ESPE safety sensor, at what distance should the test body be detected?
Question 33 of 49
When placing the test body within the door area, you are assessing the risk of which of the following?
Question 34 of 49
When testing the closing energies of an automatic door, you should hold your newton meter at what height?
Question 35 of 49
On an automatic door, the maximum permitted closing energy force you should measure is less than?
Question 36 of 49
At between what heights should signage be fitted?
Question 37 of 49
After what year would you apply the EN16005 to an installation?
Question 38 of 49
The responsibility for the display of any signage on an automatic door is the –
Question 39 of 49
If breakout is fitted, the maximum required to force the door open is?
Question 40 of 49
To measure the force to open an automatic swing door with your Newton Meter, the door must be in which position?
Question 41 of 49
In the event of a power failure and if a fail-safe is fitted then the door could adopt which of the following positions?
Question 42 of 49
Which of the following best describes the purpose of the Checklist?
Question 43 of 49
If the programme switch has a locked position, then it should –
Question 44 of 49
What is the minimum requirement for servicing an automatic door?
Question 45 of 49
When should your Newton Meter force gauge be calibrated?
Question 46 of 49
Why would you erect safety barriers when working on an automatic door?
Question 47 of 49
If your found a risk on an automatic door what should you do?
Question 48 of 49
If you test a door ESPE safety sensor and find that the CA test body is detected at 150mm then the test is a?
Question 49 of 49
There is a risk of crushing at the hinge point of an automatic door, what should you recommend?